Parts came were too short and did not clover the front of my LDO trident. Shame that the store page doesn't have specs or dimensions listed. Don't bother buying this if you have a trident, you will be about $80 out and have useless junk laying around.
Simple and fun DIY kit, works perfectly for my belt tensioning needs. Printed parts in ASA.
Make sure to read instructions carefully and make sure the calibration wire hole has enough clearance before you attempt to glue it in!
I had so many problems with klicky. Installed this and it’s awesome. Great product would buy for next printer!!
Just tried it and was immediately compelled to leave a review. It'phenominal. A bit runnier with an apple sauce consistency but the sweetness plus the hot kick is DELICIOUS. If you told me a year ago id be buying condiments from a 3d printing supplier id think you were nuts.
Plans are to incorporate this in to the X1. Shipping & product quality were excellent.
I don't typically branch out and try new filament brands but I was pleasantly surprised at how well this brand prints. I have tried a handful of different colors and had zero problems. Will continue buying
Perfect set for wiring up my VORON.
Kit came nicely packaged and will be a nice aid in wiring my VORON
Working great in my stealthburner. Klipper reports around 9600-9800rpm
Fantastic kit … well put together, everything you need to build a great printer “except printed parts”
The only thing I woud improve on is if the wiring harness is going to be changed from the original design, it may be a good idea to include a wiring guide.
My other gripe which other's have mentioned as well, the barrel connectors are garbage. You can mate them with a lot of force, but when you try to disconnect them, the barrel connector is going to disassemble itself do to its cheap contruction. I would recommend West3D to go an extra mile to fix this problem at least.
Excluding those two things, the kit would have been perfect.
After shipping it is cheaper to buy a 13 oz tube from another primary vendor versus purchasing this item alone. I considered this to save money, but it doesn't come with the syringe and what are you going to do with the remaining 12.5 oz. I've been using this syringe of grease to build a V0. I haven't even used half of it after greasing all of the rails and using some on the extruder gears. Put it in a cart with other items to spread the shipping cost out. You'll be satisfied with the purchase.
I found two methods online to grease rails. One is using the tip in a hole in the carriage. However, I found the hole in the V0 carriages to be too small for the tip. The second method, which I used, was filling the carriages from the bottom of the rail, through a mounting hole. The threaded tip of the syringe doesn't quite fit M2 sized mounting holes but I was able to seal it enough to get plenty of grease in the bearings. It seems impossible to do without getting grease everywhere so I just did my best. I hope this helps others.
Great quality hardened nozzle. Clean orifice, prints nicely.
For that last little nudge over the top and into the land of flow rate greatness and heat creep eradication.
Seriously, good stuff. Works very well.
Much rather DIY things like this and this parts kit slam dunks the convenience factor. Thanks!
Really pleased with this ASA. It prints every bit as well as Polymaker at a much nicer price. Ordering more...
Arrived pretty quick to my house. Printed a few things with and the color was great. Had some issues but it was the printer issue.
The G2 extruder kit from West3D exceeded my expectations. The quality of the components is excellent, and everything came well-packaged. Assembly was straightforward thanks to the clear and detailed instructions provided. It integrated seamlessly into my setup and delivered great performance right out of the gate. Filament loading is smooth, extrusion is consistent, and the overall print quality has improved. Highly recommend for anyone looking to upgrade to a reliable, well-supported extruder.
No issues, color was perfect!
I made my order from Germany for the Mandala Roseworks SV08 to Voron Buildplate because i wont give up on the SV08, even if it make more problems than fun. Order 26.05. and arrived well packed today on 02.06 and i got a West3D Sticker on top. Even if i did not try it for now because it came today, the Part of West3D in this Deal was awesome. If i ever need something else that is not available in 3rd-World-Germany i will order here again, even if it costs a kidney and your half lung for Delivery and Tariffs.
Thank you!
Awesome kit and very easy to put together. Surprisingly great sound quality. These quickly became my favorite headphones
